Telescopic rod to extend from 110 to 210cm, made of galvanized steel

It happens again and again that the four-legged friend climbs up the net and swings over it to go on an adventure. Our elegant telescopic pole attachment – made of steel, galvanised – angles inwards at about 115° to make climbing over difficult or impossible. The telescopic pole attachment can easily be pushed onto the telescopic pole and fastened with the locking screw. Please note that you need approx. 70 cm more net height due to the angle attachment. This telescopic pole attachment is only suitable for our extendable telescopic poles.

To achieve greater stability for your balcony net system, the telescopic rods are connected to each other using the connecting rods and connecting elements. These T-connectors are fitted on top of the extendable telescopic rods (onto the inner tube with 16 mm Ø) and permanently secured with the corresponding screw set. The spacing between the telescopic rods should not exceed 2 metres. Please note that all connecting elements offered cannot be attached to the lower end of the extendable telescopic pole. If you also wish to install a cross connection along the lower longitudinal side, you cannot use the extendable telescopic rods. In this case, you must use the connecting rods. You can then attach the connecting elements at both the top and bottom (in this case the connecting elements are slid onto the connecting rod and secured by the snap-in of the tripod spring). IMPORTANT: You do NOT need a screw when the T-connector is used together with the connecting rods. Screws are only required when the T-connector is mounted on our extendable telescopic pole. To secure the front of a balcony that is, for example, 4 m long, you will need the following parts: 2 x end connectors + screws 1 x T-connector + screws 2 x connecting rods à 2.0 m 3 x extendable telescopic rods up to 210 cm 3 x telescopic pole brackets (wall bracket, railing bracket, or masonry bracket) 1 x Boy cat net 1 x cable ties (pack of 100) If the netting is to be extended further towards the house wall, you will need an additional corner angle connector. Please refer to our installation guide and technical drawings. Frame System for a 2 m Long Balcony or Terrace Frame System for a 2.4 m to 3.8 m Long Balcony or Terrace Frame System for a 4 m Long Balcony or Terrace Frame System with Extendable Telescopic rods for a 3.5 m Long Balcony with Corner 1) End connector 2) T-connector 3) Corner angle connector 4) Connecting rod 200 cm 5) Connecting rod 100 cm 6) Connecting rod 120 - 190 cm 7) Extendable telescopic pole Frame System with Connecting Rods - Wall with Corner and Over-Climb Protection

To achieve higher stability for your balcony netting, the telescopic poles are connected to each other using connecting rods and connecting elements. These end connections are placed ABOVE on the first and last telescopic pull-out pole (on the 16 mm Ø insertion tube) and permanently fixed with the appropriate screws. **Important:** All offered connecting elements CANNOT be attached to the lower end of the telescopic pull-out pole. If you also want to install a cross connection on the lower long side, you cannot use telescopic pull-out poles. In this case, you must use connecting rods. Then you can attach the connecting elements at both top and bottom (the connecting elements are placed on the connecting rod and secured by the tension spring snapping into place). CAUTION: You need NO screw when the connecting element is used together with connecting rods. Screws are only required when mounting connecting elements on the telescopic pull-out pole. If you use telescopic pull-out poles, please don't forget to order the screws as well. Frame system with telescopic pull-out poles for a 3.5 m balcony with corner 1) End connection 2) T-connection 3) Corner angle connection 4) Connecting rod 200 cm 5) Connecting rod 100 cm 6) Connecting rod 120–190 cm 7) Telescopic pull-out pole

If the net frame is larger than 1 m x 1 m, these cross connections are required to give the net wall greater stability. The individual sections should not be larger than 1 x 1 m, as otherwise the stability of the mesh wall will suffer. We would be happy to advise you on the selection of the required parts.

To achieve greater stability for your balcony net system, the telescopic rods are connected to each other using the connecting rods and connecting elements. These corner connectors are fitted on top of the telescopic rods installed in the corners (onto the inner tube with 16 mm Ø) and permanently secured with the corresponding screws. The spacing between the telescopic rods should not exceed 2 metres. Please note that all connecting elements offered cannot be attached to the lower end of the extendable telescopic pole. If you also wish to install a cross connection along the lower longitudinal side, you cannot use the extendable telescopic rods. In this case, you must use the connecting rods. You can then attach the connecting elements at both the top and bottom (in this case the connecting elements are slid onto the connecting rod and secured by the snap-in of the tripod spring). IMPORTANT: You do NOT need a screw when the corner connectors are used together with the connecting rods. Screws are only required when the corner connectors are mounted on our extendable telescopic rods. If the balcony is also to be netted on the sides, these corner connectors are required. They are slid onto the already installed telescopic pole in the corner. Frame System with Extendable Telescopic rods for a 3.5 m Long Balcony with Corner 1) End connector 2) T-connector 3) Corner angle connector 4) Connecting rod 200 cm 5) Connecting rod 100 cm 6) Connecting rod 120 - 190 cm 7) Extendable telescopic pole

Telescopic rod clamp made of hardened Aluminium, black or aluminium coloured anodized, for balconies with a square handrail with an edge length between 4,0 and 6,0cm. This bracket will be fitted to the railing with 2 screws only. This clamp is suitable only for our extendable Boy-Telescopic rods with a diameter of 19mm.

Where no drilling is allowed, these brackets are suitable for permanent attachment of the telescopic rod for pulling out on a round balcony handrail. The sturdy telescopic rod holder made of aluminium is angled on the inside so that it tightly encloses the round handrail. The bracket is attached to the handrail with two long screws. The diameter of the round handrail must be between 30 and 60 mm. This telescopic rod holder is specially dimensioned for our telescopic rods that can be pulled out. It can therefore happen that telescopic rods not supplied by us do not fit into the intended hole. These brackets are not suitable for the telescopic rods for tensioning. NEW – in the program: Telescopic rod holders for handrails up to a diameter of 85 mm.